About grace Liu

Author Archive | grace Liu

Upgrade V60 video phone with USB device

If you will upgrade the video phone V60 to the specific firmware, you can refer to the below steps: 1. Put the firmware to your USB device; 2. Plug the USB device to the video phone; 3. Press two keys at the same time when you power on the V60 IP phone 4. The phone will go to recovery mode, we can press up and down key to choose the second option: update from USB equipment, then click OK key. 5.Choose the firmware file and click OK button: 6.The phone will start […]

Continue Reading

WX IPPBX connects with the FXO gateway

When we connect the WX IPPBX with the FXO gateway in the same network, we can realize the function like this: 1. The IP extension can dial 9+number, the call will go out through the FXO of gateway; 2. When anyone calls in the FXO of gateway, they will hear the welcome message, then can dial the extension.   For the setting, you can refer to the guide here: Let us try to set the WX IPPBX firstly. 1. Create one IP trunk for FXO gateway, here we connect the WX IPPBX with FXO gateway by IP to IP.   Registrar server: here 10.168.1.190 is the IP address of FXO gateway. Trunk ID: you can input any number, as usual, we input 100. Username: the number is same as Trunk ID. Password: any digits we can input. Concurrent: it means how many calls can go through the ip trunk at the same time. Trunk type: if we choose DID here, we need to go on choosing the extension in the next option DID, it means when we call in the ip trunk, the extension in DID will ring directly. If we choose IVR here, we need to go on choosing the voice file in the next option greeting, it means when we call in the ip trunk, we will hear the welcome message we choose: 2. Create the dialing rule. Here in order to be convenient to control the call, we choose using prefix, and set the prefix as 9, choose the ip trunk we create. It means when any extensions dial 9+any number, the call will go out through the ip trunk 100.       Let us try to set the FXO gateway. 1. Set the IP address as the static, because the IP address is in DHCP mode at default. 2.Set the routing table. IP[10.168.1.31:5070] x ROUTE FXO 1-2 It means when the gateway receives any calls from the WX IPPBX, the call will go out through the FXO 1-2. FXO x ROUTE IP   10.168.1.31:5070 It means any incoming calls from any FXO will be transferred to the WX. 3. Set the inbound calls in the gateway. Here we choose Inbound handle as Binding, and number is the IP trunk of WX IPPBX. It means when the FXO receives any incoming calls, which will be transferred to the number 100.

Continue Reading

How will the call of PABX work with VOIP gateway

As usual, we can connect the PABX with the VOIP device by the FXS or FXO, and how does the call work? here we will describe the different connections will have the different methods for dialing. Connection A: FXO of PABX connects with FXS of voip gateway. Here it is the outbound call of PABX. When the extension 7001 wants to dial the extension 8001, 7001 needs to dial 9+8001, here we assume 9 is the prefix which is used to call out through the FXO in the PABX, after that, the call will be transferred to voip gateway.       Here it is the inbound call of PABX. When the PABX receives the call from 8001 through the FXO, 8001 will hear the second dial tone firstly, then 8001 can go on dialing 7001, so 7001 will ring directly.     […]

Continue Reading

remote connection of two analog PBX

When two analog PBX or PABX are in two different offices, we hope all the extension of them can call each other for free, and two offices are in the same VPN or two offices are using the static public IP, but how will we connect them? and which device do we need? You can refer […]

Continue Reading

FAX to email in UCM

In the UCM, we can try to transfer the FAX to email when UCM receives the FAX. The related steps are as follows: We need to make sure the UCM can send email to our email. Here we take sina email as sender, in the sina email, we need to enable smtp service. After we […]

Continue Reading Comments { 0 }

Remotely connect to gateway through IP to IP

When you connect two gateways through IP to IP in the same network, they can work normally. if you hope to put them in the different networks, you need to do the below settings: 1. we need to open the sip and rtp port in the router. in the gateway, you can check the sip […]

Continue Reading Comments { 0 }

Caller ID of UCM

For the FXO of UCM, if you hope to make sure it can work normally, you can refer  to the below method: 1. we will do the ACIM detection firstly. 2. we will detect the PSTN line. if we just plug one PSTN line, we can choose semi-auto detect, and you can input your mobile […]

Continue Reading Comments { 0 }

MyPBX connects with FXS&FXO gateway

If you connect the MyPBX with FXS&FXO gateway in the same network, you can refer to the below file: Let us set the MyPBX firstly. 1. Please create one sip trunk. Here 192.168.1.195 is the IP address of gateway, and sip port is 5060, and we connect IPPBX with gateway through IP to IP. 2. […]

Continue Reading Comments { 0 }

Backup server of IP phone

When the IP phone registers to the sip server, if the main sip server is down, you can back up it to the other ip server. the setting is like this: 1. we will input the related information like this: Here the account and password of two sip server need to be same, and their server address and […]

Continue Reading Comments { 0 }

How to connect the card VC2400A

If you hope to connect the VC2400A to your sip server, here we assume you use VC2400A-24FXO, and sip server is elastix,  many points are very important: 1. before you plug the card,  you need to power off the sip server firstly,  after you plug the card, you can power on it;  2. the card has […]

Continue Reading Comments { 0 }