Upgrade V60 video phone with USB device

If you will upgrade the video phone V60 to the specific firmware, you can refer to the below steps: 1. Put the firmware to your USB device; 2. Plug the USB device to the video phone; 3. Press two keys at the same time when you power on the V60 IP phone 4. The phone will go to recovery mode, we can press up and down key to choose the second option: update from USB equipment, then click OK key. 5.Choose the firmware file and click OK button: 6.The phone will start […]

Continue Reading

WX IPPBX connects with the FXO gateway

When we connect the WX IPPBX with the FXO gateway in the same network, we can realize the function like this: 1. The IP extension can dial 9+number, the call will go out through the FXO of gateway; 2. When anyone calls in the FXO of gateway, they will hear the welcome message, then can dial the extension.   For the setting, you can refer to the guide here: Let us try to set the WX IPPBX firstly. 1. Create one IP trunk for FXO gateway, here we connect the WX IPPBX with FXO gateway by IP to IP.   Registrar server: here 10.168.1.190 is the IP address of FXO gateway. Trunk ID: you can input any number, as usual, we input 100. Username: the number is same as Trunk ID. Password: any digits we can input. Concurrent: it means how many calls can go through the ip trunk at the same time. Trunk type: if we choose DID here, we need to go on choosing the extension in the next option DID, it means when we call in the ip trunk, the extension in DID will ring directly. If we choose IVR here, we need to go on choosing the voice file in the next option greeting, it means when we call in the ip trunk, we will hear the welcome message we choose: 2. Create the dialing rule. Here in order to be convenient to control the call, we choose using prefix, and set the prefix as 9, choose the ip trunk we create. It means when any extensions dial 9+any number, the call will go out through the ip trunk 100.       Let us try to set the FXO gateway. 1. Set the IP address as the static, because the IP address is in DHCP mode at default. 2.Set the routing table. IP[10.168.1.31:5070] x ROUTE FXO 1-2 It means when the gateway receives any calls from the WX IPPBX, the call will go out through the FXO 1-2. FXO x ROUTE IP   10.168.1.31:5070 It means any incoming calls from any FXO will be transferred to the WX. 3. Set the inbound calls in the gateway. Here we choose Inbound handle as Binding, and number is the IP trunk of WX IPPBX. It means when the FXO receives any incoming calls, which will be transferred to the number 100.

Continue Reading

How will the call of PABX work with VOIP gateway

As usual, we can connect the PABX with the VOIP device by the FXS or FXO, and how does the call work? here we will describe the different connections will have the different methods for dialing. Connection A: FXO of PABX connects with FXS of voip gateway. Here it is the outbound call of PABX. When the extension 7001 wants to dial the extension 8001, 7001 needs to dial 9+8001, here we assume 9 is the prefix which is used to call out through the FXO in the PABX, after that, the call will be transferred to voip gateway.       Here it is the inbound call of PABX. When the PABX receives the call from 8001 through the FXO, 8001 will hear the second dial tone firstly, then 8001 can go on dialing 7001, so 7001 will ring directly.     […]

Continue Reading

remote connection of two analog PBX

When two analog PBX or PABX are in two different offices, we hope all the extension of them can call each other for free, and two offices are in the same VPN or two offices are using the static public IP, but how will we connect them? and which device do we need? You can refer […]

Continue Reading

Making Screensaver for IP Phone

Here we will modify the picture used for screensaver with the software PCtoLCD. Steps: Step 1: Modify the logo picture for the standby screen of IP Phones. The picture must be monochrome bitmap with the file name *.bmp. The size of logo depends on the IP Phones you choose. Here is the specific introduction: F62: […]

Continue Reading

FAX to email in UCM

In the UCM, we can try to transfer the FAX to email when UCM receives the FAX. The related steps are as follows: We need to make sure the UCM can send email to our email. Here we take sina email as sender, in the sina email, we need to enable smtp service. After we […]

Continue Reading Comments { 0 }

Network Influence to the Quality of the VoIP Communication

Sometimes when we communicate on two different networks through voip devices such as IP phones, we may find that our speech probably is intermittent or we hear some acoustic echo. These make us feel a bad communication. That is because the quality of VoIP communication will be influenced by the network environment. We can test […]

Continue Reading Comments { 0 }

Call Park on UCM6104 and IP40

Here we are going to talk about the function of Call-park on IP phone IP40. Call Park can be used in such a situation, we are making a call but for some reasons we have to leave, and we don’t want to end it, so Call Park can work. In a word, Call Park means […]

Continue Reading Comments { 0 }

PBX220 Connect with VG3X-2S/2O Gateway by No Registration

We can connect the VG3X-2S/2O gateway and the PBX220 without the registration of the FXS port to make the functions below available: IP extension and the analog extension on FXS port can call each other; IP extension can call out via the FXO port; The analog extension on FXS port can call out via FXO port; […]

Continue Reading Comments { 0 }

XML Remote Phonebook

If you hope the IP phone can get the phonebook remotely, you can refer to the method below: 1. Please create the xml file, and you can refer to the below content to input your own information: 2. Please put the xml file into the update folder of ftp server or http server, and make […]

Continue Reading Comments { 0 }